Sciemetric
Sciemetric

应用过滤器 / 单击过滤器将其删除

清除过滤器

51 结果 

resources

Application Note: Detecting Debris Under Brake Caliper Seal

End-of-line leak tests were not catching some brake caliper defects. Process anomalies such as small debris pieces, or “chips” in the seal groove were resulting in very subtle defects which were impossible to detect. Caliper defects were being discovered by vehicle assembly plants or by customers, which led to expensive warranty repairs and productivity disruptions. The manufacturer required a solution with minimal tooling and fixturing modification that would reliably improve caliper quality without affecting yield. Read our application note to learn how Sciemetric solved the problem. 

Tags: 
resources

Application Note | Cold Engine Testing: Mechanical Integrity and Fuel Systems Tests

Engine manufacturers require a reliable and cost-effective end-of-line test to catch any defects missed during engine assembly. Hot testing, with its long cycle times and requirements for dedicated resources and facilities for stations, is expensive. Read our Application Note to learn about Sciemetric's solution.

Tags: 
resources

Application Note: Crimp Nut Monitoring

A manufacturer of steering linkages required a method to measure and improve the quality and effectiveness of their idler arm assembly process, specifically the nut crimping operation. Their problem was that there was no way to determine the effectiveness of the operation as common problems such as cross-threading, missing crimp and “soft” crimping often occurred. Read this Application Note to learn how Sciemetric solved the problem.

Tags: 
resources

Application Note: Engine Assembly In-Process Testing (IPT) Using Process Signature Analysis

Why wait until end-of-line testing to find defects and root-cause when that leads to increased repair costs and lowers productivity. An engine defect can be introduced at any machining or assembly station, the sooner the defects are found the better. Sciemetric’s Engine In-process testing (IPT) solution finds and contains the defect(s) through various monitors installed along critical operations important for quality assurance, such as force, torque, leak, vibration, etc. With easy generation of yield and trend reports including full drill down, it’s fast to find to find root cause. Read the Application Note to learn more.

Tags: 
resources

Application Note: Leak Testing for Compressible Limb Sleeves

Recycled pressure cuffs must be tested prior to reuse to ensure they meet the standards. The medical company needed not only to improve the accuracy, repeatability and reliability of the test that was being done manually, but also had to collect test data records for each part. Sciemetric developed a solution that automated the test, provided clear visibility into the process and complete part traceability. Read the Application Note to learn more.

Tags: 
resources

Application Note: Long Block Verification

Missing piston rings in the engine caused a major engine manufacturer to experience excessive warranty charges from customers, and repairing this defect after the engine was installed in the vehicle was costly and time-consuming. Existing end-of-line testing was not detecting the missing piston rings or the resulting compression defects. Sciemetric’s long block verification solution applied at critical points throughout assembly identified timing, measured torque, pressure and cylinder combustion pressure related defects that were having the largest impact on their bottom line and yield. Being caught before end-of-line testing methods resulted in a decrease repair and warranty costs. Read the Application Note to learn more.

Tags: 
resources

Application Note | PSV for medical manufacturing: Product quality and risk management

How applying process signature technology helps medical device manufacturers apply risk management in a tough regulatory environment. Using a common hardware platform and software interface, Medical PSV offers a standard tool for managing risk across a wide array of medical device processes, such as: crimping, profiling, leak, swaging, functional test, welding - ultrasonic and more. Read the Application Note to learn more.

Tags: 
resources

Application Note | Rubber to Metal Bond Test: Conformance Verification

A manufacturer’s subjective method of testing rubber-to-metal bond using an application of tensile or shear load and observation of surface defects was missing defects. Sciemetric’s advanced integrity analysis system provides a cost efficient platform for testing, taking inputs from existing load cell and displacement transducers and working with additional sensors to detect even the most subtle non-visible bond defects ruptures. Read the Application Note to learn more.

Tags: 
resources
resources